ARDUINO I2C EEPROM PROGRAMMER SERIAL

When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. The higher data word address bits are not incremented, retaining the memory page row location. The data word address lower 5 bits are internally incremented following the receipt of each data word. The microcontroller must terminate the page write sequence with a stop condition. The EEPROM will respond with a zero after each data word received. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to 31 more data words. A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. The 64K EEPROM is capable of 32- byte page writes. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition.ДЄt this time the EEPROM enters an internally-timed write cycle, tWR, to the nonvolatile memory. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Write OperationsДЄ write operation requires two 8-bit data word addresses following the device address word and acknowledgment. If a compare is not made, the device will return to standby state. Upon a compare of the device address, the EEPROM will output a zero. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. The eighth bit of the device address is the read/write operation select bit. The A2, A1, and A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are allowed to float. These bits must compare to their corresponding hardwired input pins. The 64K uses the three device address bits A2, A1, A0 to allow as many as eight devices on the same bus. This is common to all 2-wire EEPROM devices. The device address word consists of a mandatory one, zero sequence (1010) for the first four most significant bits as shown. The 64K EEPROM requires an 8-bit device address word following a start condition to enable the chip for a read or write operation. 32-Byte Page Write Mode (Partial Page Writes Allowed).Write Protect Pin for Hardware Data Protection.Schmitt Trigger, Filtered Inputs for Noise Suppression.Low-Power Devices (ISB = 2 в™љ 5.5V) Available.Low-Voltage and Standard-Voltage Operation.If left unconnected, WP is internally pulled down to GND. When WP is tied high to VCC, all write operations to the upper quadrant (8/16K bits) of memory are inhibited. WRITE PROTECT (WP): The write protect input, when tied to GND, allows normal write operations. When the pins are not hardwired, the default A2, A1, and A0 are zero. When the pins are hardwired, as many as eight 32K/64K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open-collector devices.ДEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hard-wired or left not connected for hardware compatibility with AT24C16.

ARDUINO I2C EEPROM PROGRAMMER SERIAL

SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device.

The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The deviceвЂ™s cascadable feature allows up to 8 devices to share a common 2-wire (I2C) bus. The 24C64 provides 65,536 bits (8kB) of serial electrically erasable and programmable read-only memory (EEPROM) organized as 8192 words of 8 bits each.

Digital Storage Oscilloscope (DSO): Siglent SDS1104 (on ).

Component Name Buy On 1 PIC16F877A or PIC18F2550 or any other Add 1 BreadBoard Add 8 LED Add Add 1 Resistors Kit Add Add 1 Capacitors Kit Add Add 1 Jumper Wires Pack Add Add 1 LM7805 Voltage Regulator (5v) Add 1 Crystal Oscillator Add 1 PICkit2 or 3 Programmer Add 1 9v Battery or DC Power Supply Add Add Add

Arduino i2c eeprom programmer